micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com input parameter conditions min. typ. max. units input voltage range 85 265 vac input frequency 47 440 hz input current see model selection guide inrush current 115 vac 10.0 a pk 230 vac 20.0 emi meets cispr pub. 22/fcc class b safety ground leakage current 115 vac 0.1 ma 230 vac 0.3 output parameter conditions min. typ. max. units output voltage see model selection guide output current see model selection guide output voltage accuracy ?.0 ?.0 % line regulation v in = min to max ?.5 ?.0 % load regulation i o = min to max ?.5 ?.0 % ripple & noise (20 mhz) 3.3 & 5.0 vdc output 1.5 1.8 %v p-p of v o all other outputs 0.8 1.0 hold-up time 115 vac, 60 hz 15 msec temperature coef cient ?.02 %/? over voltage protection zener diode clamp 120 % of v o short circuit protection, note 3 continuous (autorecovery) overload protection, note 4 typ. 120% to 180% of output power general parameter conditions min. typ. max. units isolation voltage input to output 3,000 vac isolation test voltage input to output, flash tested for 60s 4,700 vac isolation resistance 500 vdc 100 m emi/rfi conducted en 55022 level b emc compliance electrostatic discharge (esd) iec/en 61000-4-2 level b rf field susceptibility iec/en61000-4-3 electrical fast transients/bursts on mains iec/en 61000-4-4 level 3 2 kv surge iec/en 61000-4-5 level 3 1kv/2 kv switching frequency 100 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -25 +25 +71 ? storage temperature range -40 +85 ? cooling free air convection (see derating curve) humidity rh, non-condensing 95 % physical case size 2.00 x 1.00 x 0.76 inches (50.8 x 25.4 x 19.3 mm) case material non-conductive plastic& fiberglass (ul94-v0) weight 1.55 oz (44g) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25?, gnd benign 280 khours safety standards ien 60950, iec 60950 safety approvals ien 60950, iec 60950 safety class iec 61140 class ii compact 1 x 2 inch 7w, single output ac/dc power supplies key features: 7w output power compact 1 x 2 inch case universal 85-265 vac input en60950 approved meets en55022 b meets iec safety class ii >280 khour mtbf c t 1 2 i h mpm-07s series electrical speci cations speci? cations typical @ +25c, 230 vac input voltage & rated output current, unless otherwise noted. speci? cations subject to change without notice.
model selection guide mechanical dimensions notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.01 ( 0.25) pin function 1 ac-neutral 2 ac-line 3 +vout 4 -vout pin connections not es : a ll dimensi o t ole r a n ce x . micropower direct www.micropowerdirect.com 292 page street ste d stoughton, ma 02072 tel: (781) 344-8226 fax: (781) 344-8481 e-mail: sales@micropowerdirect.com notes: 1 . load regulation is measured for an output change of 0% to 100% at nominal input line. 2. operation at no-load will not damage these units. how- ever, they may not meet all speci cations. 3. output short circuit protection is provided by a ?iccup mode?circuit. the unit recovers automatically when the fault condition is removed. 4. output overload protection is provided by a fold back current limiting circuit. 5. it is recommended that an external slow blow fuse also be used on the input for protection. see the table above for the correct rating. model number input output 1 (vout 1) ef ciency (%, typ) capacitive load (f max) fuse rating slow-blow (ma) current (a) voltage (vdc) current (a) 115 vac 230 vac max. min. MPM-07S-03 0.96 0.051 3.3 1.400 0.140 70 2,200 1,500 mpm-07s-05 0.139 0.051 5.0 1.400 0.140 73 2,200 1,500 mpm-07s-12 0.130 0.051 12.0 0.583 0.058 78 1,000 1,500 mpm-07s-15 0.130 0.051 15.0 0.466 0.047 78 1,000 1,500 mpm-07s-24 0.130 0.051 24.0 0.291 0.029 78 680 1,500 derating curve other outputs may be available contact the factory for details at: sales@micropowerdirect.com
|
